Advertisements

How to Fix Video Lag or Buffering Problem on Poco X2

Video buffering or lagging all the time can only be caused by a slow internet connection speed or you have a good internet connection then there might have some other issue. If you are also facing the same issue on your Poco X2 although you have a good internet connection, then follow the below article, we have mentioned a few methods to get rid of the issue where Video Lagging or Buffering on Poco X2.

Streaming video often results in the stoppage of the video while the video “Buffers.” Buffering means the part of the video you’re trying to watch is currently downloading. Constant buffering usually occurs if your Internet connection is slow. You can decrease the amount of buffering that occurs throughout a streaming video in Windows Media Player by adjusting the buffer time. You typically cannot adjust the buffer time through online video players; however, you can access the video and let it load completely before watching it.

Poco X2

Fix Video Lag or Buffering problem on Poco X2

Verify Signal Strength

In a lot of network issues, poor or weak signals are to blame. If your Poco X2 is showing No Service all the time recently, be sure to check how the signal bars are showing on your device. Anything lower than 3 bars is not good and can indicate a network issue.

If you are inside a building, try to go out and see if No Service goes away. If you are traveling by car, you may be transiting a dead spot. What you want to do is to move a known well-covered area. If No service remains, there may be an issue with your Poco X2. Continue troubleshooting it by following the steps below.

Check Internet Speed

Video buffering usually takes more bandwidth than normal surfing or browsing the internet. Make sure your speed enough to stream that video. There are many ways to check internet speed. In our case, we are using a website called fast.com to check internet speed.

If your internet connection speed is faster but intermittent, it may also cause video streaming to lag or buffer. To check if you have an intermittent internet connection, connect to known working wifi. If the problem continues even when internet connection speed is fast, there may be other factors involved. Continue with the troubleshooting steps below.

Troubleshoot the App

If mobile data only appears to disconnect when using a particular app, you may have an app issue at hand. Try troubleshooting the app to see what happens.

 Close an app using Recent Apps key

  • On your screen, tap the Recent Apps soft key (the one with three vertical lines on the left of the Home button).
  • Once the Recent Apps screen is shown, swipe left or right to look for the app. It should be here if you managed to run it previously.
  • Then, swipe up on the app to close it. This should force close it. If it’s not there, simply tap the Close All app to also restart all apps.

Close an app using App Info menu

  • Open ‘Settings’ from either the Quick Nav menu or the launcher.
  • Scroll Down and Tap ‘Apps’.
  • Now, tap on ‘Manage Apps’
  • Tap the More settings icon (three-dot icon, upper right).
  • Tap ‘Show All Apps’.
  • Find and tap the app.
  • Tap Force Stop.

Clear App Cache

If the above methods did not help, follow it up by clearing the apps’ cache. Here’s how it’s done:

  • Open ‘Settings’ from either the Quick Nav menu or the launcher.
  • Scroll Down and Tap ‘Apps’.
  • Now, tap on ‘Manage Apps’
  • If you’re looking for a system or default app, tap on More settings at the upper right (three-dot icon).
  • Tap ‘Show All Apps’.
  • Find and tap the appropriate app.
  • A popup window will appear with two options.
  • Tap the ‘Clear Cache’ button.
  • Restart the device and check for the problem.

Clear App Data

Clearing an app’s data will return it to its factory state.

Advertisements
  • Open ‘Settings’ from either the Quick Nav menu or the launcher.
  • Scroll Down and Tap ‘Apps’.
  • Now, tap on ‘Manage Apps’
  • If you’re looking for a system or default app, tap on More settings at the upper right (three-dot icon).
  • Tap ‘Show All Apps’.
  • Find and tap the appropriate app.
  • A popup window will appear with two options.
  • Tap the ‘Clear All Data’ button.
  • Restart the device and check for the problem.

Install Latest Software Updates

  • Open ‘Settings’ from either the Quick Nav menu or the launcher.
  • Scroll Down and Tap ‘My Device’.
  • Then tap on ‘System Update’.
  • Tap on the ‘Check for updates’.
  • If a system update is available, you’ll see the option on the screen. Tap Download and Install.
  • If your system is up to date, you will see a message stating that the system is up to date.

Here are a few things that are needed to take care while updating your Poco X2 or any device:

  • Your device must be connected to the internet.
  • Your device must have enough space to download the update.
  • Your device should have enough charge, more than 50% to install the update.

Reset Network Settings

  • Open ‘Settings’ from either the Quick Nav menu or the launcher.
  • After opening Settings, look for ‘Connection & Sharing’ and open it.
  • After opening Connection & Sharing, scroll down and tap ‘Reset Wi-Fi, mobile & Bluetooth’.
  • Now, tap ‘Reset Settings’ that is located at the center bottom of the screen.
  • Now, it will ask for your lock screen password, confirm it.
  • Now, a popup window will appear asking you the final time.
  • Finally, tap on the Ok button.
  • Tap on it and you’re good to go.

Troubleshoot apps in Safe Mode

In case you don’t know what is safe mode, in safe mode, the system temporarily disables all third-party applications you installed on your device. By doing this we can figure out which app is causing the problem. Follow the below step to turn Safe Mode on:

  • Your device must be powered on.
  • Press the power button on the phone.
  • When the power off, restart, airplane mode, wifi mode, etc. menu will be displayed, release the power button.
  • Now, long-press the Power OFF word on the screen.
  • Keep pressing this word until the Android Safe Mode message is being displayed on your phone.
  • Select to reboot into Android Safe Mode.
  • When done, a dedicated Safe Mode watermark will be displayed on your smartphone
  • Observe the phone and check for the problem.

After figuring out the apps which are creating the problem, follow the below steps to uninstall it(if required):

Advertisements
  • Open ‘Settings’ from either the Quick Nav menu or the launcher.
  • Scroll Down and Tap ‘Apps’.
  • Now, tap on ‘Manage Apps’
  • If you’re looking for a system or default app, tap on More settings at the upper right (three-dot icon).
  • Tap ‘Show All Apps’.
  • Find and tap the appropriate app.
  • Tap Uninstall.
  • Tap OK to confirm.

Clear Cache from Recovery Mode

In case you don’t know what is recovery, the first thing the bootloader rings up is the recovery. Recovery Mode refers to a special bootable partition, which contains a recovery application installed in it. And you can fix some problems with your phone. Follow the steps to clear cache from recovery mode:

  • Turn off your phone.
  • Now Press and hold Volume UP key + Power Key  on your Poco device simultaneously for a while
  • Once you see the Poco logo, you can release the button.
  • The phone is now booted in recovery mode
  • Use Volume keys to navigate to the Wipe cache partition option
  • To confirm, you can use the Power button.
  • Restart your phone

Factory Reset

Disclaimer

Factory reset will delete everything, so you want to make sure that you create a copy of your data such as photos, videos, documents, texts, etc. ahead of time.

From the Settings menu:

  • Open ‘Settings’ from either the Quick Nav menu or the launcher.
  • Scroll Down and Tap ‘My Device’.
  • Now again scroll down and tap ‘Backup & Reset’.
  • Now finally scroll till the end and tap ‘Erase all data (Factory Reset)’.
  • Now, tap on the ‘Delete all data’ button that is located at the center bottom of the screen.
  • Now, it will ask for your lock screen password, confirm it.
  • Again it will ask your Mi account password.
  • Enter the password and tap the Ok button.

From Recovery:

  • Turn off the device
  • Press and hold Volume Up key + Power Key
  • Release Power key when POCO logo appears but keep pressing Volume Up key
  • Release Volume Up key when Mi-Recovery Appears
  • Use Volume keys to select and Power key to confirm
  • Select Wipe Data and press power key to confirm
  • Select wipe all data and press power key to confirm
  • Select Confirm press power key to confirm
  • Select “back to main menu” by press power key
  • Select Reboot and press power key to confirm
  • Select Reboot to System and press the power key to confirm.

Conclusion

That was it, this was the easiest way to Fix Video Lag or Buffering problem on Poco X2. Follow them carefully to get benefits of the feature in your Poco X2. Are you facing any problems and issues with your Poco X2? Then there is nothing to worry about, we have an article dedicated to Poco X2’s issues and guides. Here is the Poco X2 Troubleshooting Guide. Although it’s rare, some cases of the issues on Poco devices may have bad hardware as the origin. If a factory reset won’t help in fixing your issue, visit your local Mi Store or Service Center so a qualified technician can examine the hardware. If needed, they may send it in for repair or replacement.

Do you own a Poco Device, or any Android device and need these types of simple tutorials? Then stay tunned to GetDroidTips’ Android Tips & Tricks column because many simple tutorials for Poco are coming soon.

If you have any queries regarding this, the comment section always available for you.

Leave a Reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.