It supports calibration of:
- AFC (Automatic Frequency Control)
- APC (Automatic Power Control)
- AGC (Automatic Gain Control)
These calibrations help improve signal quality, transmission stability, and overall cellular performance.
The tool performs comprehensive RF testing based on 3GPP standards, including:
- TX Power
- Phase Error
- Spectrum Emission
- ACLR
- EVM
- Receiver Sensitivity
- RF Stability Verification
These tests help identify defective hardware before devices reach customers.
Current Consumption Testing
Spreadtrum CFT can measure device current in different operating states, including:
- Power Off
- Idle Mode
- Deep Sleep
- Charging Mode
This allows manufacturers to detect excessive power consumption and abnormal current leakage during production.
System Configuration and Automation
To improve manufacturing efficiency, CFT supports several automation features, including:
- Auto-start when a device is connected
- Multiple production line roles (CFT, FT Only, Antenna Test)
- Automated testing workflow
- Detailed log generation
- Handover configuration between production stations
These features make it suitable for high-volume production environments.
You can download the latest versions of the Spreadtrum CFT Tool for Windows below.
System Requirements:
Before using the tool, make sure your computer meets the following requirements.
Supported Operating Systems
- Windows XP
- Windows Vista
- Windows 7
- Windows 8
- Windows 8.1
- Windows 10
- Windows 11
Supports both 32-bit and 64-bit versions of Windows.
Requirements
- Unisoc (Spreadtrum) USB Drivers
- Windows PC or Laptop
- USB Data Cable
- Supported Unisoc-powered device
- Administrator privileges
- Compatible RF test equipment (for factory calibration)
- Download the preferred version of the Spreadtrum CFT Tool.
- Extract the downloaded ZIP package.
- Install the required Unisoc USB drivers.
- Run the installer or launch the executable file as Administrator.
- Complete the installation process.
- Restart your computer if prompted.
Follow these steps to perform calibration and testing on a supported Unisoc device.
Step 1: Install Required Drivers
Install the latest Unisoc USB drivers on your Windows computer.
Run the Spreadtrum CFT Tool with Administrator privileges.
Choose the appropriate operating mode, such as:
depending on your testing requirements.
Step 4: Connect the Device
Boot the supported Unisoc smartphone into the required factory or calibration mode and connect it to the PC via USB.
Step 5: Start Calibration
Select the desired calibration or testing module, such as:
- Battery Calibration
- RF Calibration
- Current Consumption Test
- Final RF Test
Step 6: Review Test Results
After the process completes, the tool will display detailed pass/fail results along with log information for each completed test.
Important
Spreadtrum CFT Tool is intended primarily for factory production lines and authorized service centers. Some advanced calibration functions require dedicated RF equipment and specialized hardware.
Spreadtrum CFT is commonly used together with:
- Research Download Tool
- Upgrade Download Tool
- Factory Download Tool
- CheckX Tool
- Simba Tool
These utilities complement each other throughout the Unisoc manufacturing and servicing workflow.
Frequently Asked Questions (FAQs)
It is used to calibrate and verify RF performance, battery parameters, current consumption, and hardware functionality on Unisoc-powered smartphones during manufacturing and servicing.
No. CFT is a calibration and testing tool. To flash firmware, use Research Download Tool or Upgrade Download Tool.
Which devices are supported?
The tool supports smartphones and tablets powered by Unisoc (Spreadtrum) chipsets.
Most publicly available versions can be downloaded and used without licensing, although factory-specific releases may require authorization.
Why is my device not detected?
Make sure:
- Unisoc USB drivers are installed.
- The device is in the correct factory or calibration mode.
- The USB cable is working properly.
- Windows detects the device correctly.
What is RF calibration?
RF calibration adjusts radio parameters such as frequency, gain, and transmission power to ensure optimal cellular network performance.
Some basic functions may work without additional hardware, but complete RF calibration and final testing typically require specialized production equipment.
Which Windows versions are supported?
Spreadtrum CFT Tool supports Windows XP through Windows 11, including both 32-bit and 64-bit editions.
Conclusion
Spreadtrum CFT Tool is an essential calibration and production testing utility for Unisoc-powered devices. It enables manufacturers and technicians to perform battery calibration, RF tuning, current consumption analysis, and final hardware verification efficiently. When used alongside other Unisoc tools such as Research Download Tool and CheckX Tool, it helps ensure devices meet quality standards before deployment.
If you have any questions about the Spreadtrum CFT Tool or encounter any issues while using it, feel free to leave a comment below.
