Motorola Moto G52 XT2221-1 Firmware Flash File (Stock ROM Guide)

Motorola Moto G52 was launched in India and features a 6.6-inch full-HD+ pOLED display with a 90Hz refresh rate. The phone is powered by the Qualcomm Snapdragon 680 SoC, along with Adreno 610 GPU and up to 6GB of LPDDR4X RAM. Moto G52 comes with a triple rear camera setup which includes a 50 MP primary sensor, an 8 MP ultra-wide-angle lens, and a 2 MP macro lens.

On this page, we have shared the download link and guide to installing the Motorola XT2221-1 (Moto G52) firmware flash file using the fastboot method. Here you will find all stock firmware zip files for all the supported regions with Motorola Moto G52 XT2221-1

If you are someone who wants to restore the device to factory firmware, then this guide is for you. By using this guide, you can fix certain software-related issues such as hard brick, soft brick, WiFi, or Bluetooth issue, fix lag or stutter, or even you can downgrade the device anytime.

Motorola Moto G52 Device Overview:

The Motorola Moto G52 features a 6.6-inches AMOLED display with a 90 Hz refresh rate. It is an FHD+ panel with a resolution of 1080 x 2400 pixels and an aspect ratio of 20:9. Under the hood, we have the Qualcomm Snapdragon 680 built on a 6nm manufacturing process. It is an octa-core processor with four Kryo 265 Gold cores clocked at 2.4 GHz and four Kryo 265 Silver cores clocked at 1.9 GHz. For handling the graphics-intensive tasks, we have the Adreno 610.

In terms of optics, we get a triple camera setup at the rear and a single camera at the front. The triple camera consists of a 50 MP primary sensor paired with an f/1.8 lens, an 8 MP ultrawide sensor paired with an f/2.2 lens, and a 2MP macro sensor paired with an f/2.4 lens. The s at the front is a 16MP sensor paired with an f/2.5 lens. Both the rear and the front setup are limited to 1080p video recording.

The smartphone is available with only a single storage variant with 128GB of internal storage and 4GB of RAM. There is a MicroSD slot for storage expansion. In terms of communications, we get Wi-Fi 802.11 a/b/g/n/ac, Bluetooth 5.0, GPS, NFC, and USB Type-C 2.0. And in terms of sensors, we get a side-mounted fingerprint sensor, accelerometer, gyro, proximity, and compass. Powering it all is a 5,000 mAh battery that can be topped up quickly using a 30W power adapter. The smartphone is available in two color options: Charcoal Gray and Porcelain White.

Steps to Install Moto G52 Stock Firmware (Flash File)

Now, if you’re ready to flash the stock firmware manually on your Motorola Moto G52 XT2221-1 device then you need to download the flash tool, firmware file, and necessary drivers. So, without wasting any more time, let’s get into it.

Pre-Requirements:

• This ROM is supported for the Motorola Moto G52 XT2221-1 (rhode) variant only.
• Make sure that your device should be charged at least 50% or higher.
• You will require a PC or Laptop with a USB Data Cable.
• We always recommend that our readers take a full data backup of the device for safety.
• Install Motorola USB Drivers and Rescue and Smart Assistant Tool on your PC
• To flash, you must download the ADB and Fastboot tool

Motorola Moto G52 XT2221-1 Firmware Flash Files:

Firmware Installation Guide:

Check out the firmware flashing guide below for the Motorola Moto G52 XT2221-1 First, make sure to install or extract the adb and fastboot tool on your PC. Now enter the bootloader on your device.

Step 1. Bootloader Mode

Enter bootloader mode on your phone. To boot first, turn your phone off. Once your device is turned off completely, press and hold the volume down, and turn it on. You should see the bootloader screen.

Step 2. Connect Your Device to PC:

After booting your Motorola Moto G52 into bootloader mode, now connect it to the PC using the USB Cable.

Step 3. Download Stock ROM/Firmware:

To get the full ROM, you can use the LMSA or Rescue and Smart Assistant Tool. Download the zip file and copy it to somewhere on your PC. LMSA tool will unzip the file and will remove the zip file you downloaded.

You can also download the full stock ROM from the above download flash file section on this guide.

Step 4. Flashing Guide:

1. 1. The next step is to open the command window and go to the adb folder
   2. Enter the following command to flash the firmware

      fastboot oem fb_mode_set 
      fastboot flash partition gpt.bin 
      fastboot flash bootloader bootloader.img 
      fastboot flash vbmeta vbmeta.img
      fastboot flash vbmeta_system vbmeta_system.img
      fastboot flash vendor_boot vendor_boot.img   
      fastboot flash bluetooth BTFM.bin 
      fastboot flash radio radio.img 
      fastboot flash dsp dspso.bin 
      fastboot flash dtbo dtbo.img 
      fastboot flash logo logo.bin 
      fastboot flash boot boot.img 
      fastboot flash recovery recovery.img 
      fastboot flash super super.img_sparsechunk.0 
      fastboot flash super super.img_sparsechunk.1 
      fastboot flash super super.img_sparsechunk.2 
      fastboot flash super super.img_sparsechunk.3 
      fastboot flash super super.img_sparsechunk.4 
      fastboot flash super super.img_sparsechunk.5 
      fastboot flash super super.img_sparsechunk.6
      fastboot flash super super.img_sparsechunk.7
      fastboot flash super super.img_sparsechunk.8
      fastboot flash super super.img_sparsechunk.9
      fastboot flash super super.img_sparsechunk.10

   3. Toggle back to bootloader. Do the following:

      fastboot flash erase userdata 
      fastboot flash erase carrier 
      fastboot flash erase apdp 
      fastboot flash erase ddr 
      fastboot flash erase metadata 
      fastboot oem fb_mode_clear 
      fastboot reboot

   4. Now your device will reboot into the bootloader with the firmware you installed.

That’s it, guys. We hope this guide was helpful to you. Feel free to ask in the comment below for additional queries.