Advertisements

Xiaomi Mi 10T / 10T Pro Test Point | EDL Mode 9008 | ISP EMMC PinOUT

In this guide, we will show you the real image of the ISP pinout and test point for the Xiaomi Mi 10T Pro (apollo). By using the ISP PinOUT, you can easily restore the stock ROM, bypass FRP lock, or reset user data on your device via UFi Box. In this guide, we will also guide you on how to reboot into 9008 EDL Mode.

Xiaomi Mi 10T Pro Device Overview:

Xiaomi Mi 10T / 10T Pro Test Point | EDL Mode 9008 | ISP EMMC PinOUT

Talking about the Mi 10T Pro, it has a bigger 6.67-inches IPS LCD display with 1080×2400 pixels resolution, HDR10+, 144Hz refresh rate, 500 nits typ. brightness, a 20:9 aspect ratio, etc. It runs on Android 10 with the MIUI 12 skin out of the package. The device is equipped with an octa-core Qualcomm Snapdragon 865 SoC, Adreno 650 GPU, 8GB RAM, 128GB/256GB of internal storage capacity, etc.

In terms of the connectivity option, the handset packs a dual-band Wi-Fi 802.11 a/b/g/n/ac/6, Wi-Fi Direct, Bluetooth 5.1, GPS, dual-band A-GPS, GLONASS, BDS, GALILEO, QZSS, NFC, Infrared Port, USB Type-C, etc. While it sports a 5,000mAh battery with 33W quick charging support. A couple of major sensors like a side-mounted fingerprint sensor, an ambient light sensor, gyroscope, proximity, compass, and accelerometer also available.

Now, coming to the camera specifications, the handset packs a triple rear camera setup that includes a 108MP (wide, f/1.7), a 13MP (ultrawide, f/2.4), a 5MP (macro, f/2.4) lens with the PDAF, OIS, HDR, Panorama, an LED flash, etc. On the front side, the device packs a single 20MP selfie camera (wide, f/2.2) that offers HDR mode.

What is ISP PinOUT?

ISP or In-system programming also known as in-circuit serial programming (ICSP) for hardware that has a cross-reference of pins or contacts. By shorting the pins together, you can power or signal the logic board (motherboard) of an electronic device such as a mobile, computer. You will find the IS Pinout connection on the logic board of your device. Therefore, you will need to remove the back panel of the handset and follow the below image to locate the pinout.

Xiaomi Mi 10T Pro ISP Pinout Image:

Xiaomi-Mi-10T-Pro-5G-Test-Point

How to Enter EDL Mode on Xiaomi Mi 10T Pro (apollo)

Follow this instruction carefully to boot your device into EDL Mode (aka Emergency DownLoad Mode)

Method 1: Using ADB

  • Download ADB and Fastboot Tool and extract it to your PC (C:/ Drive)
  • Connect your device to your PC
  • Open the adb command and enter the command
    .\adb reboot edl

Method 2: Using Fastboot

  • Download ADB and Fastboot Tool and extract it to your PC (C:/ Drive)
  • Boot your device into the bootloader
  • Open the command window on your PC on the same folder extracted (ADB and Fastboot Tool)
  • now enter the command
    .\fastboot oem edl

Method 3: By Hardware Test Points / Restore Your device

  • Download the QDLoader driver
  • Find the EDL PinOUT/Test Point on your device (refer to image above to find the test point)
  • To enter EDL mode, you need to use a metal tweezer or a conductive metal wire to short the points.
  • Once you are done, connect your device to the PC using a USB cable
  • This way, your device will enter EDL mode. Now you can open the QFil or QPST Tool to flash the firmware and restore your device.

I hope this guide was helpful to find the Xiaomi Mi 10T Pro (apollo) ISP Testpoints.

Leave a Reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.