Motorola Edge X30 XT2201-1 Firmware Flash File (Stock ROM Guide)

Motorola Edge X30 launched their first Motorola phone to come with a hidden display selfie camera. Apart from the new front-facing camera, the Moto Edge X30 is powered by an octa-core Snapdragon 8 Gen 1 SoC and features a 120Hz display. The device sports a triple rear camera setup that houses a 50 MP primary sensor, along with a 50 MP wide-angle shooter and a 2 MP depth sensor.

On this page, we have shared the download link and guide to install the Motorola XT2201-1 (Moto Edge X30) firmware flash file using the fastboot method. Here you will find all stock firmware zip files for all the supported regions with Motorola Edge X30 XT2201-1

If you are someone who wants to restore the device back to factory firmware, then this guide is for you. By using this guide, you can fix certain software-related issues such as hard brick, soft brick, WiFi, or Bluetooth issue, fix lag or stutter or even you can downgrade the device anytime.

Motorola Edge X30 XT2201-1 Firmware Flash File (Stock ROM Guide)

Steps to Install Moto Edge X30 Stock Firmware (Flash File)

Now, if you’re ready to flash the stock firmware manually on your Motorola Edge X30 XT2201-1 device then you need to download the flash tool, firmware file, and necessary drivers. So, without wasting any more time, let’s get into it.

Pre-Requirements:

Disclaimer:

GetDroidTips will not be held responsible for any kind of hardware or software damage to your device by following this guide. Proceed at your own risk

Motorola Edge X30 XT2201-1 Firmware Flash Files:

Flash File Name: S1SH32.55-8-8
Model: XT2201-1
Android Version: 12.0
Download

Firmware Installation Guide:

Check out the firmware flashing guide below for the Motorola Edge X30 XT2201-1 First, make sure to install or extract the adb and fastboot tool on your PC. Now enter the bootloader on your device.

bootloader mode

Step 1. Bootloader Mode

Enter bootloader mode on your phone. To boot first, turn your phone off. Once your device is turned off completely, press and hold the volume down, and turn it on. You should see the bootloader screen.

Step 2. Connect Your Device to PC:

After booting your Motorola Edge X30 into bootloader mode, now connect it to the PC using the USB Cable.

Step 3. Download Stock ROM/Firmware:

To get the full ROM, you can use the LMSA or Rescue and Smart Assistant Tool. Download the zip file and copy it to somewhere on your PC. LMSA tool will unzip the file and will remove the zip file you downloaded.

device rescue Motorola Rescue and Smart Assistant Tool

You can also download the full stock ROM from the above download flash file section on this guide.

Step 4. Flashing Guide:

    1. The next step is to open the command window and go to the adb folder Open Command Window here
    2. Enter the following command to flash the firmware
      fastboot oem fb_mode_set 
      fastboot flash partition gpt.bin 
      fastboot flash bootloader bootloader.img 
      fastboot flash vbmeta vbmeta.img
      fastboot flash vbmeta_system vbmeta_system.img
      fastboot flash vendor_boot vendor_boot.img   
      fastboot flash bluetooth BTFM.bin 
      fastboot flash radio radio.img 
      fastboot flash dsp dspso.bin 
      fastboot flash dtbo dtbo.img 
      fastboot flash logo logo.bin 
      fastboot flash boot boot.img 
      fastboot flash recovery recovery.img 
      fastboot flash super super.img_sparsechunk.0 
      fastboot flash super super.img_sparsechunk.1 
      fastboot flash super super.img_sparsechunk.2 
      fastboot flash super super.img_sparsechunk.3 
      fastboot flash super super.img_sparsechunk.4 
      fastboot flash super super.img_sparsechunk.5 
      fastboot flash super super.img_sparsechunk.6
      fastboot flash super super.img_sparsechunk.7
      fastboot flash super super.img_sparsechunk.8
      fastboot flash super super.img_sparsechunk.9
      fastboot flash super super.img_sparsechunk.10
      fastboot flash super super.img_sparsechunk.11
      fastboot flash super super.img_sparsechunk.12
      fastboot flash super super.img_sparsechunk.13
      fastboot flash super super.img_sparsechunk.14
    3. Toggle back to bootloader. Do the following:
      fastboot flash erase userdata 
      fastboot flash erase carrier 
      fastboot flash erase apdp 
      fastboot flash erase ddr 
      fastboot flash erase metadata 
      fastboot oem fb_mode_clear 
      fastboot reboot
    4. Now your device will reboot into bootloader with the firmware you installed.

That’s it, guys. We hope this guide was helpful to you. Feel free to ask in the comment below for additional queries.

Leave a Reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.