Oppo Reno 2Z CPH1945 ISP UFS PinOUT | Test Point | EDL Mode 9008

In this guide, we will show you the real image of the ISP pinout and test point for the Oppo Reno 2Z CPH1945. By using the ISP PinOUT, you can easily restore the stock ROM, bypass FRP lock, or reset user data on your device via UFi Box. In this guide, we will also guide you on how to reboot into 9008 EDL Mode.

What is ISP PinOUT?

ISP or In-system programming also known as in-circuit serial programming (ICSP) for hardware that has a cross-reference of pins or contacts. By shorting the pins together, you can power or signal the logic board (motherboard) of an electronic device such as a mobile, computer. You will find the IS Pinout connection on the logic board of your device. Therefore, you will need to remove the back panel of the handset and follow the below image to locate the pinout.

Oppo Reno 2Z ISP Pinout Image:

Oppo Reno 2Z CPH1945 ISP UFS PinOUT | Test Point | EDL Mode 9008
Image Credits to tuserhp.com

Oppo Reno 2Z Specifications:

It has a 6.53-inches AMOLED display with Corning Gorilla Glass 5 protection. The handset runs on Android 9.0 Pie over ColorOS 6.1 skin out-of-the-box and upgradable to Android 10. The device is powered by Mediatek MT6779 Helio P90 SoC, coupled with PowerVR GM9446 GPU. It packs an 8GB of RAM and 256GB of internal storage option.

The handset sports a quad-camera setup on the rear side consists of a 48MP wide, an 8MP ultra-wide, a 2MP B/W, and a 2MP depth sensor also. It also has Dual-LED flash, HDR, Panorama, PDAF, and more. While the front features a 16MP wide-angle pop-up selfie camera with an f/2.0 aperture lens.

In terms of the connectivity options, it has a 3.5mm audio jack, Wi-Fi 802.11 a/b/g/n/ac, dual-band Wi-Fi, Bluetooth 5.0, GPS, A-GPS, GLONASS, FM Radio, USB Type-C port, and more. The device features an in-display Fingerprint sensor, an accelerometer, a gyroscope, proximity, compass, etc. It packs a 4000mAh battery with 20W VOOC Flas Charge 3.0 fast charging support.

How to Enter EDL Mode on Oppo Reno 2Z (CPH1945)

Follow this instruction carefully to boot your device into EDL Mode (aka Emergency DownLoad Mode)

Method 1: Using ADB

  • Download ADB and Fastboot Tool and extract it in your PC (C:/ Drive)
  • Connect your device to your PC
  • Open the adb command and enter the command
    .\adb reboot edl

Method 2: Using Fastboot

  • Download ADB and Fastboot Tool and extract it in your PC (C:/ Drive)
  • Boot your device into bootloader
  • Open the command window on your PC on the same folder extracted (ADB and Fastboot Tool)
  • now enter the command
    .\fastboot oem edl

Method 3: By Hardware Test Points / Restore Your device

  • Download the QDLoader driver
  • Find the EDL PinOUT/Test Point on your device (refer image above to find the test point)
  • To enter EDL mode, you need to use a metal tweezer or a conductive metal wire to short the points.
  • Once you are done, connect your device to the PC using a USB cable
  • This way, your device will enter EDL mode. Now you can open the QFil or QPST Tool to flash the firmware and restore your device.

I hope this guide was helpful to find the Oppo Reno 2Z CPH1945 ISP Testpoints.

Leave a Reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.