How to Install Stock ROM on Motorola Edge Plus XT2061-3 (Firmware Guide)

The US-based Motorola is owned by the Chinese vendor Lenovo now. The brand has unveiled its new device i.e., the Motorola Edge Plus, as a Verizon exclusive. It gets a 6.7″ display, Snapdragon 865, 12GB RAM, 256GB ROM, quad rear cameras, 5000mAh battery, and runs on Android 10. In this tutorial, we will help you to flash the stock firmware on Motorola Edge Plus XT2061-3.

If you are someone who wants to restore the device back to factory firmware, then this guide is for you. By using this guide, you can fix certain software-related issues such as hard brick, soft brick, WiFi, or Bluetooth issue, fix lag or stutter or even you can downgrade the device anytime.

How to Install Stock ROM on Motorola Edge Plus XT2061-3 (Firmware Guide)

The Need to Flash Stock Firmware on Motorola Edge Plus

One common query that would come to your mind is why to manually flash the firmware when the device would be getting the OTA updates. Well, this is quite a valid concern from your end. So here’s the thing. The OEM usually releases the updates in batches. In other words, this is a staged rollout where not everyone gets the update at one go. But if you have got hold of the update package, then you could easily cut this wait time and manually flash the stock firmware right away.

Then if you are among the tech enthusiasts, you might consider going for device modifications. These would include the likes of unlocking bootloader, flashing custom recoveries, or rooting it via Magisk. While on one side all these would end up adding new features to your device. However, on the other hand, a slight mistake would end up your device in a boot loop or soft-brick state.  But even then you could bring back your device from dead by flashing the stock firmware onto your Motorola Edge Plus device. And in this guide, we will help you with just that.

Steps to Install Motorola XT2061-3 Stock Firmware (Flash File)

Now, if you’re ready to flash the stock firmware manually on your Motorola Edge Plus XT2061-3 device then you need to download the flash tool, firmware file, and necessary drivers. So, without wasting any more time, let’s get into it.



GetDroidTips will not be held responsible for any kind of hardware or software damage to your device by following this guide. Proceed at your own risk

Motorola Edge Plus XT2061-3 Firmware Flash Files:

    Flash File Name: S1PBS32.41-10-17-3
    Model: XT2061-3
    Android Version: 12
    Flash File Name: RPBS31.Q1-19-19-14-17
    Model: XT2061-3
    Android Version: 11
    Flash File Name: RPBS31.Q1-19-19-14-5
    Model: XT2061-3
    Android Version: 11
    Flash File Name: RPB31.Q1-19-19-14
    Model: XT2061-3
    Android Version: 11
    Flash File Name: QPBS30.188-58-9
    Model: XT2061-3
    Android Version: 10
    Flash File Name: QPBS30.188-58-5
    Model: XT2061-3
    Android Version: 10

    Firmware Installation Guide:

    Check out the firmware flashing guide below for the Motorola Edge Plus XT2061-3. First, make sure to install or extract the adb and fastboot tool on your PC. Now enter the bootloader on your device.

    bootloader mode

    Step 1. Bootloader Mode

    Enter bootloader mode on your phone. To boot first, turn your phone off. Once your device turned off completely, press and hold volume down, and turn it on. You should see the bootloader screen.

    Step 2. Connect Your Device to PC:

    After booting your Motorola Edge Plus into bootloader mode, now connect it to the PC using the USB Cable.

    Step 3. Download Stock ROM/Firmware:

    To get the full ROM, you can use the LMSA or Rescue and Smart Assistant Tool. Download the zip file and copy it to somewhere on your PC. LMSA tool will unzip the file and will remove the zip file you downloaded.

    device rescue Motorola Rescue and Smart Assistant Tool

    You can also download the full stock ROM from the above download flash file section on this guide.

    Step 4. Flashing Guide:

    1. The next step is to open the command window and go to the adb folder Open Command Window here
    2. Enter the following command to flash the firmware.
      fastboot oem fb_mode_set
      fastboot flash partition gpt.bin 
      fastboot flash bootloader bootloader.img
      fastboot flash logo logo.bin 
      fastboot flash vbmeta vbmeta.img
      fastboot flash boot boot.img
      fastboot flash dsp dspso.bin 
      fastboot flash dtbo dtbo.img
      fastboot flash recovery recovery.img 
      fastboot flash super super.img_sparsechunk.0
      fastboot flash super super.img_sparsechunk.1
      fastboot flash super super.img_sparsechunk.2
      fastboot flash super super.img_sparsechunk.3
      fastboot flash super super.img_sparsechunk.4
      fastboot flash super super.img_sparsechunk.5
      fastboot flash super super.img_sparsechunk.6
      fastboot flash super super.img_sparsechunk.6 
      fastboot flash modem NON-HLOS.bin
      fastboot flash fsg fsg.mbn
      fastboot flash bluetooth BTFM.bin
      fastboot oem fb_mode_clear
      fastboot erase userdata (Do it, if you want to clear all your data)

    That’s it, guys. We hope this guide was helpful to you. Feel free to ask in the comment below for additional queries.

    Leave a Reply

    Your email address will not be published. Required fields are marked *

    This site uses Akismet to reduce spam. Learn how your comment data is processed.