Motorola G7 Power XT1955-2 Firmware | Stock ROM

On this page, we have shared the download link and guide to install the Motorola XT1955-2 (Moto G7 Power, codenamed ocean) firmware flash file using the fastboot method. Here you will find all stock firmware zip files for all the supported regions with Motorola G7 Power XT1955-2.

If you are someone who wants to restore the device back to factory firmware, then this guide is for you. By using this guide, you can fix certain software-related issues such as hard brick, soft brick, WiFi, or Bluetooth issue, fix lag or stutter or even you can downgrade the device anytime.

Motorola Moto G7 Power – Device Specifications

Motorola Moto G7 Power comes with Qualcomm Snapdragon 632 chipset which is coupled with 3/4 GB of RAM. It offers 32/64 GB of onboard storage which can be expanded via the dedicated microSD card slot. The display of the device is 6.2-inches at a resolution of 720 x 1570 pixels at an aspect ratio of 19.5:9 and 279 PPI density. The display is protected with Corning Gorilla Glass 3.

In the camera department, it has a single 12MP camera shooter that is capable of recording 4K@30fps and 1080p@30fps. While the front camera is an 8MP lens that is capable of recording 1080p@30fps. Under the hood, the device packs a massive 5000 mAh battery that supports fast charging 15W or 18W. The fingerprint sensor is located on the back of the phone. Out of the box, it comes with Android 9 Pie and is running the latest Android 10 update.

Steps to Install Motorola XT1955-2 Stock Firmware (Flash File)

Now, if you’re ready to flash the stock firmware manually on your Motorola G7 Power XT1955-2 device then you need to download the flash tool, firmware file, and necessary drivers. So, without wasting any more time, let’s get into it.

Pre-Requirements:

• This ROM is supported for the Motorola G7 Power XT1955-2 (Ocean) variant only.
• Make sure that your device should be charged at least 50% or higher.
• You will require a PC or Laptop with a USB Data Cable.
• We always recommend our readers take a full data backup of the device for safety purposes.
• Install Motorola USB Drivers and Rescue and Smart Assistant Tool on your PC
• To flash, you must download the ADB and Fastboot tool

Motorola G7 Power XT1955-2 Firmware Flash Files:

Firmware Installation Guide:

Check out the firmware flashing guide below for the Motorola G7 Power XT1955-2. First, make sure to install or extract the adb and fastboot tool on your PC. Now enter the bootloader on your device.

Step 1. Bootloader Mode

Enter bootloader mode on your phone. To boot first, turn your phone off. Once your device turned off completely, press and hold volume down, and turn it on. You should see the bootloader screen.

Step 2. Connect Your Device to PC:

After booting your Motorola G7 Power into bootloader mode, now connect it to the PC using the USB Cable.

Step 3. Download Stock ROM/Firmware:

To get the full ROM, you can use the LMSA or Rescue and Smart Assistant Tool. Download the zip file and copy it to somewhere on your PC. LMSA tool will unzip the file and will remove the zip file you downloaded.

You can also download the full stock ROM from the above download flash file section on this guide.

Step 4. Flashing Guide:

1. The next step is to open the command window and go to the adb folder
2. Enter the following command to flash the firmware.

   fastboot flash partition gpt.bin 
   fastboot flash bootloader bootloader.img 
   fastboot flash dsp adspso.bin 
   fastboot flash modem NON-HLOS.bin 
   fastboot flash radio radio.img 
   fastboot flash logo logo.bin

3. Now toggle the fastbootd

   fastboot reboot fastboot

4. Again flash the following command

   fastboot flash boot boot.img
   fastboot flash dtbo dtbo.img
   fastboot flash super super.img.sparsechunk.0
   fastboot flash super super.img.sparsechunk.1
   fastboot flash super super.img.sparsechunk.2
   fastboot flash super super.img.sparsechunk.3
   fastboot flash super super.img.sparsechunk.4
   fastboot flash super super.img.sparsechunk.5
   fastboot flash super super.img.sparsechunk.6
   fastboot flash super super.img.sparsechunk.7
   fastboot flash super super.img.sparsechunk.8
   fastboot flash super super.img.sparsechunk.9
   fastboot flash super super.img.sparsechunk.10
   fastboot flash system_b system_b.img_sparsechunk.0
   fastboot flash system_b system_b.img_sparsechunk.1
   fastboot flash vendor vendor.img_sparsechunk.0
   fastboot flash vendor vendor.img_sparsechunk.1

5. Toggle back to bootloader. Do the following:

   fastboot reboot bootloader
   fastboot erase ddr
   fastboot erase ddr
   (Optional except you want to wipe) fastboot erase userdata
   fastboot reboot

6. Now your device will reboot into bootloader with the firmware you installed.

That’s it, guys. We hope this guide was helpful to you. Feel free to ask in the comment below for additional queries.