How to Install Stock ROM on Motorola G6 XT1925-6 (Firmware Guide)

Want to install the stock firmware on your Motorola Moto G6? then you are in the right place. In this guide, we will help you in installing the official stock firmware on Motorola G6 (codenamed ali) variant XT1925-6. Stock firmware comes in handy when you mess up your device to root it or install a mod or custom ROM. To be on the safe side, we always ask our users to download the official firmware on their PC and save it.

By installing firmware flash file on Moto G6 XT1925-6, you can unbrick, restore, fix any software related issue, downgrade or upgrade, resolve any bugs or lag on your device. To install the Moto G6 XT1925-6 firmware, you need the ADB and Fastboot tool on your computer.

Moto G6 XT1925-6 Firmware Flash Files:

Steps to Install Motorola XT1925-6 Firmware Flash File

If you have downloaded the firmware, then follow this guide to flash the stock firmware manually on your Moto G6 XT1925-6. Make sure to follow the steps carefully.

Pre-Requirements:

• This ROM is supported for the Moto G6 XT1925-6 (ali) variant only.
• Make sure that your device should be charged at least 50% or higher.
• You will require a PC or Laptop with a USB Data Cable.
• We always recommend our readers take a full data backup of the device for safety purposes.
• Install Motorola USB Drivers and Rescue and Smart Assistant Tool on your PC
• To flash, you must download the ADB and Fastboot tool

Firmware Installation Guide:

Check out the firmware flashing guide below for the Moto G6 XT1925-6. First, make sure to install or extract the adb and fastboot tool on your PC. Now enter the bootloader on your device.

Step 1. Bootloader Mode

Enter bootloader mode on your phone. To boot first, turn your phone off. Once your device is turned off completely, press and hold the volume down, and turn it on. You should see the bootloader screen.

Step 2. Connect Your Device to PC:

After booting your Moto G6 into bootloader mode, now connect it to the PC using the USB Cable.

Step 3. Download Stock ROM/Firmware:

To get the full ROM, you can use the LMSA or Rescue and Smart Assistant Tool. Download the zip file and copy it to somewhere on your PC. LMSA tool will unzip the file and will remove the zip file you downloaded.

You can also download the full stock ROM from the above download flash file section on this guide.

Step 4. Flashing Guide:

1. The next step is to open the command window and go to the adb folder
2. Enter the following command to flash the firmware.

   fastboot flash partition gpt.bin
   fastboot flash bootloader bootloader.img
   fastboot flash modem NON-HLOS.bin
   fastboot flash fsg fsg.mbn
   fastboot erase modemst1
   fastboot erase modemst2
   fastboot flash bluetooth BTFM.bin
   fastboot flash dsp adspso.bin
   fastboot flash boot boot.img
   fastboot flash system system.img_sparsechunk.0
   fastboot flash system system.img_sparsechunk.1
   fastboot flash system system.img_sparsechunk.2
   fastboot flash system system.img_sparsechunk.3
   fastboot flash system system.img_sparsechunk.4
   fastboot flash system system.img_sparsechunk.5
   fastboot flash system system.img_sparsechunk.6
   fastboot flash system system.img_sparsechunk.7
   fastboot flash system system.img_sparsechunk.8
   fastboot flash system system.img_sparsechunk.9
   fastboot flash system system.img_sparsechunk.10
   fastboot flash vendor vendor.img_sparsechunk.0
   fastboot flash vendor vendor.img_sparsechunk.1
   fastboot erase carrier
   fastboot erase userdata
   fastboot erase DDR
   fastboot flash logo logo.bin
   fastboot oem fb_mode_clear
   fastboot reboot

3. Now your device will reboot into bootloader with the firmware you installed.

That’s it, guys. We hope this guide was helpful to you. Feel free to ask in the comment below for additional queries.