Verizon Motorola G7 Power XT1955-6 Firmware | Stock ROM Guide

In this guide, we’ll be sharing the easy steps to install the Verizon Motorola XT1955-6 (G7 Power) firmware flash file (codenamed Ocean). As an open-source platform, Android devices do come with plenty of customization options which can also lead to bricking or stuck in the boot loop issue due to unsupported file flashing or even improper flashing steps. Needless to say that most Android users want to heavily customize their devices via flashing third-party firmware files or rooting.

In some cases, the device performance may become slow, starts lagging, networking issues, etc. So, installing the stock firmware on your Verizon Moto G7 Power device will bring back a stable life like before.

Verizon Motorola G7 Power XT1955-6 Firmware | Stock ROM Guide

Steps to Install Verizon Motorola XT1955-6 Firmware Flash File

Now, if you’re ready to flash the stock firmware manually on your Motorola G7 Power XT1955-6 device then you need to download the flash tool, firmware file, and necessary drivers. So, without wasting any more time, let’s get into it.

Pre-Requirements:

Disclaimer:

GetDroidTips will not be held responsible for any kind of hardware or software damage to your device by following this guide. Proceed at your own risk

Motorola G7 Power XT1955-6 Firmware Flash Files:

Firmware File Name: QCOS30.85-18-9
Model: XT1955-6
Region: USA (Verizon)
Android Version: 10.0
Download
Firmware File Name: PDOS29.114-134-15
Model: XT1955-6
Region: USA (Verizon)
Android Version: 9.0 Pie
Download

Firmware Installation Guide:

Check out the firmware flashing guide below for the Verizon Moto G7 Power XT1955-6. First, make sure to install or extract the adb and fastboot tool on your PC. Now enter the bootloader on your device.

bootloader mode

Advertisements

Step 1. Bootloader Mode

Enter bootloader mode on your phone. To boot first, turn your phone off. Once your device turned off completely, press and hold volume down, and turn it on. You should see the bootloader screen.

Step 2. Connect Your Device to PC:

After booting your Motorola Moto G7 Power into bootloader mode, now connect it to the PC using the USB Cable.

Step 3. Download Stock ROM/Firmware:

To get the full ROM, you can use the LMSA or Rescue and Smart Assistant Tool. Download the zip file and copy it to somewhere on your PC. LMSA tool will unzip the file and will remove the zip file you downloaded.

device rescue Motorola Rescue and Smart Assistant Tool

Advertisements

You can also download the full stock ROM from the above download flash file section on this guide.

Step 4. Flashing Guide:

    1. The next step is to open the command window and go to the adb folder Open Command Window here
    2. Enter the following command to flash the firmware.
      fastboot flash partition gpt.bin 
      fastboot flash bootloader bootloader.img 
      fastboot flash dsp adspso.bin 
      fastboot flash modem NON-HLOS.bin 
      fastboot flash radio radio.img 
      fastboot flash logo logo.bin
    3. Now toggle the fastbootd
      fastboot reboot fastboot
    4. Again flash the following command
      fastboot flash boot boot.img
      fastboot flash dtbo dtbo.img
      fastboot flash super super.img.sparsechunk.0
      fastboot flash super super.img.sparsechunk.1
      fastboot flash super super.img.sparsechunk.2
      fastboot flash super super.img.sparsechunk.3
      fastboot flash super super.img.sparsechunk.4
      fastboot flash super super.img.sparsechunk.5
      fastboot flash super super.img.sparsechunk.6
      fastboot flash super super.img.sparsechunk.7
      fastboot flash super super.img.sparsechunk.8
      fastboot flash super super.img.sparsechunk.9
      fastboot flash super super.img.sparsechunk.10
      fastboot flash system_b system_b.img_sparsechunk.0
      fastboot flash system_b system_b.img_sparsechunk.1
      fastboot flash vendor vendor.img_sparsechunk.0
      fastboot flash vendor vendor.img_sparsechunk.1
    5. Toggle back to bootloader. Do the following:
      fastboot reboot bootloader
      fastboot erase ddr
      fastboot erase ddr
      (Optional except you want to wipe) fastboot erase userdata
      fastboot reboot
    6. Now your device will reboot into bootloader with the firmware you installed.

That’s it, guys. We hope this guide was helpful to you. Feel free to ask in the comment below for additional queries.

Leave a Reply

Your email address will not be published.

This site uses Akismet to reduce spam. Learn how your comment data is processed.